Use a single set for many sizes of internal and external threads. All sets include tap and die wrenches.

Repair screw threads in a wide range of sizes.

These taps are for use on most metal and plastic.

Multiple tap sizes allow tapping a range of hole diameters. Connect these taps directly to drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

Create pipe and conduit threads in a range of hole diameters.

All taps and drill bits have a hex shank for direct connection to tools such as drills and power screwdrivers.

Repair rusted or damaged external threads in a variety of sizes.

Clamp these dies around your workpiece, so you can start thread repair anywhere along the length of a bolt, stud, or rod.

Cut threads into most metal and plastic.

Sized to cut oversized threads, these tools are often used to tap holes where the threads will shrink due to heat treatment or plating.

Often used for thread repair and occasional hand tapping, these carbon steel taps can thread holes in most metal and plastic, but they have a shorter tool life than standard taps.

Keep chips clear while tapping. Also known as gun taps, these have spiral-point flutes that push chips ahead of the tap and out of through holes.

These taps cut left-hand threads while keeping chips clear.

The spiral flute design pulls chips back toward the tap, so chips won't accumulate in closed-end holes.

With a drill bit point to drive into the workpiece, these taps can drill and tap holes in a single step. A 1/4" hex shank connects them directly to tools such as drills and power screwdrivers.

Drill holes and cut threads without switching tools.

These taps are made of cobalt steel for higher strength and wear resistance than standard taps. Their flutes are designed to keep chips clear, so they don't need to be reversed to prevent buildup.

Coated with chromium carbide or titanium carbonitride (TiCN), these cobalt steel taps cut smoothly through soft material to produce accurate threads.

Create threads sized for pipe and conduit.

Tap left-hand threads for pipe and conduit.

With a taper chamfer on one threading end and a bottoming chamfer on the other, these pipe and conduit taps can start threads easily, and they are able to thread close to the bottom of closed-end holes.

Also known as interrupted-thread taps, these have extra space between the cutting threads, so large chips fall without packing and high amounts of lubricant can flow between the tap and the workpiece.

The spiral flutes on these pipe and conduit taps keep chips clear by drawing them back out of the hole, so there's no need to reverse the tap while cutting threads.

Made of cobalt steel, these taps are for use on steel pipe and conduit.

Use with a tap to thread holes by hand. These wrenches are more compact than straight-handle tap wrenches, so they can be used to tap in tighter spaces.

Connect a tap to these wrenches for occasional or light-duty hand tapping. All have a T-handle design, so they're more compact than straight-handle tap wrenches but provide less leverage.

For occasional or light-duty hand tapping, connect a tap to these wrenches. They have long handles to provide more leverage than T-handle wrenches, but they require more space for tapping.

Powered by compressed air, these tap wrenches thread holes faster and with less effort than manual tap wrenches.

Extend the length of your tap to access hard-to-reach areas.

Sets include multiple holders for use with different tap sizes. These holders work like sockets to connect taps to ratchet wrenches.

These steel cases close for easy transport and are labeled with sizes for organizing tools. Taps and drill bits are not included.

After using a large-diameter bit to drill a starter hole in a broken tap, drill out the tap with one of these tools. Sets include multiple removers for use with different tap sizes and two picks for removing the remains.

To extract taps of different sizes, these sets include multiple extractors. Use them with a tap wrench to remove taps with straight flutes from the workpiece without damaging the surrounding threads.

Restore bolt, hole, pipe, and conduit threading with this set of four files.

Repair rusted and damaged threads in pipe and conduit. These files are for use in most hole diameters.

Attach these tools to a socket wrench to restore rusted and damaged spark plug threads in two common sizes.

For use with a wide range of threaded hole diameters, these sets include multiple retrievers. Insert the retriever into a tapped hole and pull out to remove chips.

Use these dies to create external threads on bolts, studs, and rods.

Create external pipe and conduit threads.

Each set includes a ratchet with handle, die heads, and dies. Use them to cut NPT threads in steel pipe and conduit by hand.

Add or replace parts such as drive adapters, die sets, and drive bars for the Ridgid Large Size Pipe and Conduit Threader Adapter.

Carry this pipe and conduit threader to your work site.

These machines thread faster than the Ridgid 300 and include a self-lubricating die head and automatic chuck.

Use these dies with Ridgid pipe and conduit threader die heads on Ridgid pipe and conduit threaders.

Cut threads in PVC with the specially designed teeth on these high-speed steel dies.

Restore rusted and damaged screw threads. These dies are hex shaped for use with conventional wrenches.

A smaller width than standard hex dies lets you repair threads in tight spaces.

Clamp these dies around your workpiece, so you can start thread repair anywhere along the length of a bolt, stud, or rod. They're hex shaped for use with conventional wrenches.

Renew rusted and damaged pipe and conduit threads.

Repair rusted and damaged threads on any diameter bolt, stud, or rod.

One file restores pipe and conduit threads in many sizes.

Also known as die stocks, these wrenches grip round dies so you can turn them by hand.