The most common of our flexible high-temperature sheets, these are used to insulate furnaces.

Made of high-strength calcium silicate, these durable sheets withstand high temperatures and are often used in power-generating applications.

Thinner than most rigid insulation for furnaces and other high-heat applications, these millboard sheets are also used for gasket fabrication.

Even when subjected to heavy compression, these rigid polyimide sheets won't crack.

Commonly used in furnaces and engine compartments, these flexible silica fiber sheets resist corrosive acids.

Insulate high-vacuum furnaces and other low-oxygen vacuum enclosures with these flexible sheets.

Designed for fluctuating, high-temperature applications, these semi-rigid sheets are typically used in furnaces and fire protection applications. They experience very little shrinkage at high temperatures, but the brittle material can be somewhat difficult to work with.

Wet these rigid sheets and they become formable. They can be molded multiple times until exposed to heat, which causes them to become rigid again.

Often used in furnaces, these firebricks have been machined for a snug fit to minimize heat loss.

Set and repair cast iron and steel furnaces, heaters, stoves, and boilers with this ready-to-use cement. It experiences minimal shrinkage for a permanent smokeproof and gasproof joint. Apply with a trowel or a spatula.

Shield against extreme heat with these flexible ceramic strips. They are often used to insulate hose, cables, and process piping.

Less flexible than rubber foam, this insulation restricts absorption of water, air, and gas. It is typically used in plumbing applications

Rigid and flame resistant, these insulation tubes are typically used in process piping and mechanical systems.

Superior in strength and durability, these thin strips insulate as well as protect personnel from accidental contact with hot pipes. Use for exhaust, hot water, and process pipes.

Very rigid with a 0% water absorption rate, this insulation is unaffected by corrosive environments, organic solvents, and most acids. It is typically used in chemical-processing systems and underground lines.

Reduce the risk of burns from accidental contact with hot pipes under your sink. These molded, flexible pipe covers are ADA compliant when properly installed.

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

Able to withstand temperatures as low as -290° F, these super-thin, lightweight sheets are made of fiber-reinforced silica aerogel that can flex into tight spaces other insulation can't. Use in process piping and power-generating applications.

Protect insulation from light impact and moisture with this durable PVC jacketing.

Wrap pipes, tubing, and fittings to prevent condensation from forming. These strips are for use on copper, iron, and steel.

Prevent condensation from forming on refrigeration and air conditioning lines and cold‐water piping.

Cover large areas with this two-part expanding foam insulation.

Expanding quickly to fill large voids, this foam insulation begins to harden in 4 minutes and can be cut within 10 minutes.

Also known as batts, these fiberglass sheets and strips are used to insulate walls, ceilings, and floors.

Form this reusable putty around metal pipes and tubing or spread on a flat metal surface to stop heat from traveling to adjoining surfaces when soldering, welding, and brazing.

Use these sheets in operating temperatures below 32° F, such as cold-storage applications.

Wrap rectangular and round ductwork with this flexible insulation.

Also known as fire wrap, these flame-resistant sheets meet ASTM E84 0/0 for flame and smoke and create a fire barrier around rectangular and round ductwork. They are often used to wrap kitchen grease exhaust ducts and air ducts.

Seal fiberglass duct and insulation that's faced with an all-service jacket (ASJ). Tape is reinforced with fiberglass.

Made with fiberglass for durability and abrasion resistance, this tape also withstands high temperatures.

Fiberglass is laminated with Teflon® PTFE for a slippery, durable tape with excellent chemical and temperature resistance. Use it as a release surface on heat sealers and blister forming equipment.

This tape discharges minor amounts of surface static electricity and resists static buildup.

Use this tape to wrap and splice cables, mask components while soldering, or as a 3D printing surface.

In addition to handling temperatures up to 500° F, this fiberglass tape is tough enough for abrasive applications such as sand blasting.