Threaded Rod End Fittings | McMaster-Carr

Filter by

Thread Size

Material

Beryllium Copper

Stainless Steel

System of Measurement

ID

OD

Retaining Ring Type

Shank Thread Size

Finish

Black Zinc Plated

Corrosion-Resistant Coated

Hot-Dipped Galvanized

Phosphate Coated

Nut Type

With Sight Hole

Retaining Ring Style

Constant Section

Groove Diameter

Gender

Length

Hex Length

RoHS

Compliant with Exemptions

DFARS Specialty Metals

REACH

Rod End Type

Ball Joint Linkage

Export Control Classification Number (ECCN)

Ring Thickness

Shank Gender

Ring OD

Thread Length

Shank Center Length

Ring ID

Width

How can we improve?

10,374 Products

Material Handling

Threaded Rod Mounts

Threaded Rod Mounts

Hang threaded rod from ceilings, walls, beams, and joists

Threaded Rod Anchors

Threaded Rod Anchors

Install directly into a flat surface for more holding power than threaded rod mounts

Pipe Hangers

Suspend pipe, conduit, and tube from threaded rods, hooks, and straps

Beam Clamps

Secure lines of pipe and duct, overhead equipment, and lighting fixtures to beam flanges

Threaded Rod Hanger Beams

Threaded Rod Hanger Beams

Mount across roof joists to hang threaded rod and route pipe and duct in areas with no anchor point

Routing Clamps

Secure routed lines of pipe, tubing, and conduit

Vibration-Damping Hangers

Vibration-Damping Hangers

Reduce vibration and noise in suspended equipment, such as air-handling units, pipe, and duct

Eye Nuts

Pair with bolts or threaded rod to lift and hang components

Turnbuckles

Twist the body or end fittings to adjust the length and tension of attached rope and chain

Wire Rope End Fittings

Wire Rope End Fittings

Finish wire rope ends with threaded stud, eye, clevis, ball, hook, and other connections

Lanyards

Pull, hang, tie down, and tether objects with the attached fittings

Screw Jack End Fittings

Screw Jack End Fittings

Thread onto screw jacks to create pivot points with clevis rod ends and other linkages

Conveyor Track Brackets

Conveyor Track Brackets

Hang and join sections of enclosed conveyor track

Power Transmission

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Rod End Nuts

Attach to rods, pipe, and tubing to make pivot and hinge points

Hydraulic Cylinder Mounts

Hydraulic Cylinder Mounts

Restrain cylinders and secure loads to the end of the rod

Shaft Adapters

Increase or reduce your shaft's diameter to fit equipment, or replace damaged shaft ends

Gas Spring End Fittings

Gas Spring End Fittings

Connect gas springs to mounting studs and brackets

Fastening and Joining

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Coupling Nuts

Connect and extend threaded rods

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Hex Nuts

Handle most general fastening needs

Split Nuts

Swivel to attach at any point on a threaded rod for quick installation

Weld Nuts

Weld to metal surfaces to add permanent threads

Push Nuts

Press onto threads for a light duty hold that’s faster to install than typical nuts

Tube-Connecting Nuts

Tube-Connecting Nuts

Push inside tubes to join them with a threaded stud instead of welding

Clip-On Nuts

Slide onto the edge of thin panels to create a fastening point

Snap-In Nuts

Push into square holes in thin materials to add bolts for aligning off-center parts

Retaining Rings

Retaining Rings

Hold components on a shaft

Snap-In Nut Tools

Snap-In Nut Tools

Compress the legs of snap-in nuts so they're easy to install and remove

Building and Machinery Hardware

Protective Caps

Protective Caps

Protect just about anything, including pipe, flanges, screws, and posts

Strut Mount Hangers

Strut Mount Hangers

Quickly attach and reposition conduit, rod, and chain along strut channel without using fasteners

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)