Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

A metal body provides more strength and durability than plastic. These valves have a low-profile handle and a short end-to-end length to fit in tight spots. All are for use with water, oil, air, and inert gas. They divert flow between ports.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

Barbed fittings on these valves grip onto tubing, providing a secure hold. To divert flow between ports in chemical-processing applications, they have a chemical-resistant seal and a PVDF body to withstand aggressive and corrosive solutions.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They divert flow between ports in food and beverage tubing lines.

Barbed fittings on these valves grip onto tubing, providing a secure hold. They divert flow between ports in food and beverage tubing lines.

Bolt these valves to flanges. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Often used in sanitary valve manifolds, these 3-A certified valves can be cleaned in place to eliminate the risk of cross contamination in food, beverage, and dairy lines. All have sanitary quick-clamp fittings for easy disassembly. They operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

Often used for chemical analysis and other laboratory testing, these valves have a PTFE seal and body to withstand aggressive and corrosive solutions. They operate on electricity to automatically divert flow between ports.

Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

Because they require a key to operate, you can limit who is able to adjust these valves. They create one action, such as extending a cylinder.

The push buttons that operate these valves are separate from the logic unit, allowing you to position them away from machinery. Since both hands are required to simultaneously press the buttons, they protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

These valves are rated for environments where hazardous material is present. They actuate when voltage is applied to the electrical connection.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 3-way or 3/2 valves.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.