We will reply to your message within an hour.
More
Also known as Oilite® bearings.
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.
Handle heavy loads that frequently start and stop along shafts—these bearings contain extra iron and slippery PTFE lubricant. They’re thrust bearings, which means they support loads parallel to the shaft.
The oil in these bearings is NSF registered H1 and FDA compliant for incidental contact with food.
Made of 863 iron-copper and embedded with NSF registered H1 oil, these bearings can tackle high-load applications in food plants, such as bottling and filling lines.
Use where high loads and speeds are not required.
A metal backing adds strength.
Graphite provides a layer of dry lubrication that operates in high-temperature environments.
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Good for underwater applications, these bearings won’t swell or warp when wet.
Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.
These bearings stand up to a wider range of chemicals than other dry-running thrust bearings.
These bronze bearings are strong, wear resistant, and excellent at handling shock loads.
The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.
With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications.
The oil in these bearings is suitable for incidental contact with food.
Support heavy loads that are often found in bottling and filling lines in food plants—these bearings contain extra iron and FDA-compliant oil. They’re flanged, so they handle loads both parallel and perpendicular to the shaft.
These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.
A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.
Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.
An aluminum shell adds strength.
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.
Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.
Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.
Furnished with a traceable lot number and material test report, these bronze bearings are strong, wear resistant, and excellent at handling shock loads.
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings.
Cylindrical-roller thrust bearings handle higher loads than needle-roller thrust bearings. They also run at faster speeds than tapered-roller thrust bearings.
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components.
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings.
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
Use these bearings as miniature high-precision turntables. They have a unique design that allows your shaft to sit on top of the bearing rather than being inserted through it.
Made of high-performance plastic, these insert bearings last longer than metal insert bearings. They also don’t require lubrication.
Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.