Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

For a strong, secure connection, mount these hangers by welding them to a rod.

Cut as much strap as you need to hang duct, pipe, and other materials.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.