Tube Marking Tools | McMaster-Carr

	Length Length

	Width Width

2 5/8"

3 7/8"

5 1/4"

	For System of Measurement For System of Measurement

Inch

Metric

	Graduation Marks Graduation Marks

2.5°

2 mm

16ths

	Numeric Increments Numeric Increments

10°

1 cm

	Maximum Diameter , Outer (Pipe) (For) Maximum Diameter , Outer (Pipe) (For)

	Material Material

Aluminum

Rubber

	DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense Acquisition Regulations Supplement)

DFARS Specialty Metals
COTS-Exempt

	Punch Operation Punch Operation

Manual

Spring Loaded

	Minimum Diameter , Outer (Pipe) (For) Minimum Diameter , Outer (Pipe) (For)

1 1/2"

2 mm

	Measuring Length Measuring Length

28 "

36 "

	RoHS (Restriction of Hazardous Substances) RoHS (Restriction of Hazardous Substances)

RoHS Compliant

	For Minimum Pipe OD For Minimum Pipe OD

1/2"

	Probe Material Probe Material

Stainless Steel

Plastic

	For Pipe Size For Pipe Size

1 1/4

1 1/2

2 1/2

	For Contour Length For Contour Length

5 1/4"

10"

	For Contour Width For Contour Width

1 1/4"

	For Pipe OD For Pipe OD

	REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration, Evaluation, Authorization and Restriction of Chemicals)

REACH Compliant

Forward

How can we improve?

15 Products

Center-Locating Punches for Curved Surfaces

Locate and mark the centerline on rods, tubes, and pipes, lay out keyways, and establish angles for connections.

Manual locator is for use with a hammer. Gently strike the rod to mark the center.

Spring-loaded locator marks the center with the pull of a trigger.

Punch Operation	Angle Measuring Range	Graduation Marks	Numeric Increments	For Min. Pipe OD	Material	Punch Material	Includes	Features		Each
Manual	0°-90°	2.5°	10°	1/2"	Aluminum	Steel	Adjustable Dial Protractor	Bubble Level	000000	0000000
Spring Loaded	0°-90°	2.5°	10°	1"	Aluminum	Steel	Adjustable Dial Protractor	Bubble Level	000000	000000

Replacement Dial/Level Assembly

0000000

Each

000000

Pipe Contour Transfer Markers

Lay out pipe and structural steel for any type or size of pipe fitting—elbows, tees, and wyes of all angles. These markers are lightweight aluminum.

Anodized Aluminum
For Pipe OD	Angle Measuring Range	Graduation Marks (Numeric Increments)	Mount Type	Marker Type	Includes		Each
1 1/2"-18"	0°-90°	2.5° (10°)	Magnet	Soapstone Crayon	Calibrated Protractor Dials, Holder for Soapstone Crayon, Level, Magnetic Base, Triple-Jointed Marking Arm	000000	0000000
8"-48"	0°-90°	2.5° (10°)	Magnet	Soapstone Crayon	Built-in Bubble Level, Calibrated Protractor Dials, Holder for Soapstone Crayon, Magnetic Base, Triple-Jointed Marking Arm	000000	000000

Pipe Contour Transfers

Push Down

Slide Up and Mark

Probes take the shape of a pipe joint so you can transfer the exact outline to the pipe before you cut.

For Pipe
Size	OD	Probe Material		Each
1	1 5/16"	Stainless Steel	0000000	000000
1 1/4	1 5/8"	Stainless Steel	0000000	00000
1 1/2	1 7/8"	Stainless Steel	0000000	00000
2	2 3/8"	Stainless Steel	0000000	00000
2 1/2	2 7/8"	Stainless Steel	0000000	000000

Contour Transfers

Transfer contours, patterns, and shapes for applications such as fitting floor tile and installing pipe insulation. A series of narrow probes slide within a frame to duplicate any shape.

For Contour
Lg.	Wd.	Probe Material	Lg.		Each
5 1/4"	2"	Stainless Steel	6"	0000000	00000
10"	1 1/4"	Plastic	11 1/8"	00000000	00000

Pipe Size Rulers

Measure outer diameter and mark lines around pipe. A pipe size conversion chart is printed on these rulers. They’re fiber-reinforced rubber for grease, oil, gasoline, and salt water resistance.

For Pipe OD
Inch	Metric	Lg.	Wd.	Thick.	Measuring Lg.	Front Graduation Marks (Numeric Increments)	Color	Graduation Color	Max. Temp.		Each
Rubber
1"-6"	2 mm-60 cm	30"	2 5/8"	3/64"	28"	2 mm (1 cm), 16ths (1")	Gray	White	360° F	0000000	000000
2"-16"	2 mm-78 cm	60"	3 7/8"	3/64"	36"	2 mm (1 cm), 16ths (1")	Gray	White	360° F	0000000	00000
6"-30"	2 mm-77 cm	120"	5 1/4"	3/64"	36"	2 mm (1 cm), 16ths (1")	Gray	White	360° F	0000000	00000