We will reply to your message within an hour.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Suspend and route flat-bottomed objects such as strut channel and small duct.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Route pipe, tubing, and conduit across strut channel.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
Hold pipe, tubing, and conduit away from strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.
Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.
Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.
Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.
Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.
Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.
For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.
Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.
Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.
For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.
Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.
Combine with a U-bolt or routing clamp to convey a variety of material, such as pipe, tubing, and cable raceway, at distance from floors, walls, and ceilings. The extra clearance allows access for maintenance and adding and removing lines.
Add a crossbeam for hanging lifting equipment, creating overhead conveyor systems, and supporting structural applications.
Join two beams in a straight line.
Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.
A toothed clip secures these clamps to the beam—no fasteners required.
These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.
Also known as purlin clamps, these clamps are shaped to fit around beams that have a 45° or 90° lip.
For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.
A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.
Support strut channel at a right angle to the beam.
Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
These clamps have a fixed hanger for rigid connections.
Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.
For a strong, secure connection, mount these hangers by welding them to a rod.
Clamp onto metal tubes such as pipe, scaffolding, and railing to hang lighting fixtures, threaded rod, and equipment.
Also known as angle brackets.
Connect wood 2×4s to posts and other flat surfaces.
Clamp these brackets to panel edges to quickly assemble crates.
No need to drill holes in panels—tighten the set screw to hold them in place.
Designed to wrap around the sides of strut channel, these brackets provide a stronger hold than other strut channel brackets.
These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.
Brackets mount on the outside of strut channel to allow trolley movement.
Up to two times the height of regular strut channel, this high-profile channel is stronger than regular strut channel.
Half the height and the same width as regular strut channel, this low-profile strut channel fits into tight spots and is compatible with many of the same brackets.
Run cable and tubing in the tightest spaces with channel that is one-quarter the height and one-half the width of regular strut channel.
Create continuous runs of channel without corners.
For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.
This welded, one-piece strut channel combines two strut channels side-to-side.
This welded, one-piece strut channel combines two strut channels back-to-back.
Slide the strut channel into the tube for telescoping length adjustments.
These rails have continuous T-slots for attaching fittings. Use this versatile framing to configure machine guards, enclosures, carts, and workstations.
More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.
An anodized coating on these U-channels forms a bond with the aluminum surface to improve wear and corrosion resistance.
The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.
Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.
The open top allows U-channels to slide over an edge. Use them as seals and trim.
Use one of these kits to replace rusty or broken hardware on urinal partitions.
These kits include all brackets and fasteners needed for mounting partitions.
Combine track, mounting brackets, and hangers to create a system for hanging doors.
Round track eliminates edges where dust and debris can accumulate.
Curved track pieces allow you to create a wide variety of layouts for doors, curtains, and strip doors.
Use these brackets for extra mounting space behind DIN rail to accommodate wiring and bulky items.
Protect development boards from dust, water, and debris by mounting them to DIN rails inside control cabinets.
These steel rod ends are machined to SAE standards.
Made of zinc-plated steel or stainless steel, these clevis rod ends offer more corrosion resistance than standard steel clevis rod ends.
In addition to offering superior chemical resistance, these lightweight, fiber-reinforced nylon rod ends also reduce noise and vibration.
Thread or weld the unfinished shank of these rod ends to meet your specific linkage needs.
Make quick adjustments to these rod ends by inserting and releasing the clevis pins without the need to bend them into place.
A male-threaded shank lets you build a linkage with a tapped tube or any female-threaded connection.
Use these guides to position a rope.
Clamp around a pipe or tube to guide rope.
Install these mounts on machines without feet.
Slide 1/4"-20 hex head screws anywhere along the track to create mounting points for clamps and jigs.