McMaster-Carr logo
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    37 Products

    Vernier Calipers

    Image of ProductInUse. Front orientation. Contains Annotated. Calipers. Vernier Calipers.
    Image of Product. Front orientation. Calipers. Vernier Calipers.
    Your traditional calipers, combining precision and durability. This classic design uses a sliding vernier scale. Just add the measurement from the main scale to the measurement on the vernier scale to get accurate readings as small as 0.001". Made completely out of metal, these calipers won't break when dropped or short-circuit when wet. They're battery-free, so they're always ready to use.
    Mitutoyo—The go-to for machinists and engineers. Every part of these calipers is made within Mitutoyo's automated system and tested in-house in Japan. Their jaws are laser cut to exact dimensions for the most reliable measurements.
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Calipers
    Inch
    Metric,
    mm
    Inch
    Metric
    Inch
    Metric,
    mm
    Overall
    Lg.
    Body Material
    Jaw Material
    Mfr. Model
    No.
    Each
    Mitutoyo
    0" to 6"±0.0015"0.001"9"Stainless Steel
    Stainless Steel
    530-1058619A680000000
    0" to 6"0 to 150±0.0012"±0.03 mm0.001"0.029"Stainless Steel
    Stainless Steel
    530-3128619A67000000
    0" to 12"0 to 300±0.0015"±0.04 mm0.001"0.0216"Stainless Steel
    Stainless Steel
    530-1198619A52000000
     
    Other Calipers
    0" to 4"±0.001"0.001"6 3/16"Stainless Steel
    Stainless Steel
    2192A2200000
     
    Depth Base Attachments
    Image of Product. Front orientation. Caliper Depth Base Attachments. Mitutoyo.

    Mitutoyo

    Clamp onto the end of your caliper to steady it while measuring depth.
    For Caliper Measurement Range
    Each
    Mitutoyo
    0" to 4", 0" to 6", 0" to 8", 0 mm to 100 mm, 0 mm to 150 mm, 0 mm to 200 mm2325A45000000
    0" to 12", 0 mm to 300 mm2325A4700000
     

    Precision-Adjust Vernier Calipers

    Image of ProductInUse. Front orientation. Contains Annotated. Calipers. Precision-Adjust Vernier Calipers.
    Image of Product. Front orientation. Calipers. Precision-Adjust Vernier Calipers.
    Move the jaws exactly where you need them. The fine-adjustment wheel opens and closes the jaws in small, precise increments for extra control while measuring.
    These classic calipers use a sliding vernier scale. Just add the measurement from the main scale to the measurement on the vernier scale to get accurate readings as small as 0.001". Made completely out of metal, they won't break when dropped or short-circuit when wet. They're battery-free, so they're always ready to use.
    Mitutoyo—The go-to for machinists and engineers. Every part of these calipers is made within Mitutoyo's automated system and tested in-house in Japan. Their jaws are laser cut to exact dimensions for the most reliable measurements.
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Calipers
    Inch
    Metric,
    mm
    Inch
    Metric
    Inch
    Metric,
    mm
    Overall
    Lg.
    Body Material
    Jaw Material
    Mfr. Model
    No.
    Each
    Mitutoyo
    0" to 18"0 to 450±0.002"±0.05 mm0.001"0.0224 3/4"Stainless Steel
    Stainless Steel
    160-1518619A810000000
    0" to 24"0 to 600±0.002"±0.05 mm0.001"0.0230 3/4"Stainless Steel
    Stainless Steel
    160-1538619A8300000000
    0" to 40"0 to 1,000±0.003"±0.07 mm0.001"0.0248 3/4"Stainless Steel
    Stainless Steel
    160-1558619A8500000000
     
    Other Calipers
    0" to 6"0 to 150±0.001"±0.025 mm0.001"0.027"Stainless Steel
    Stainless Steel
    8619A5300000
    0" to 8"0 to 200±0.0015"±0.04 mm0.001"0.0211 1/2"Stainless Steel
    Stainless Steel
    2272A2300000
    0" to 12"0 to 300±0.0015"±0.04 mm0.001"0.0216"Stainless Steel
    Stainless Steel
    2272A2400000
     

    Self-Locking Vernier Calipers

    Image of ProductInUse. Front orientation. Contains Annotated. Calipers. Self-Locking Vernier Calipers.
    Image of Product. Front orientation. Calipers. Self-Locking Vernier Calipers.
    Prevent the jaws from creeping forward or backward as you measure. They move only when you press a button, then lock in place when you let go. The button falls naturally under your thumb, so you can operate these calipers comfortably with one hand.
    These classic calipers use a sliding vernier scale. Just add the measurement from the main scale to the measurement on the vernier scale to get accurate readings as small as 0.001". Made completely out of metal, they won't break when dropped or short-circuit when wet. They're battery-free, so they're always ready to use.
    Mitutoyo—The go-to for machinists and engineers. Every part of these calipers is made within Mitutoyo's automated system and tested in-house in Japan. Their jaws are laser cut to exact dimensions for the most reliable measurements.
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Calipers
    Inch
    Metric,
    mm
    Inch
    Metric
    Inch
    Metric,
    mm
    Overall
    Lg.
    Body Material
    Jaw Material
    Mfr. Model
    No.
    Each
    Mitutoyo
    0" to 8"0 to 200±0.0012"±0.03 mm0.001"0.0211 1/4"Stainless Steel
    Stainless Steel
    531-1292064A310000000
     
    Other Calipers
    0" to 6"0 to 150±0.0015"±0.04 mm0.001"0.029"Stainless Steel
    Stainless Steel
    2272A2100000
     
    Depth Base Attachments
    Image of Product. Front orientation. Caliper Depth Base Attachments. Mitutoyo.

    Mitutoyo

    Clamp onto the end of your caliper to steady it while measuring depth.
    For Caliper Measurement Range
    Each
    Mitutoyo
    0" to 4", 0" to 6", 0" to 8", 0 mm to 100 mm, 0 mm to 150 mm, 0 mm to 200 mm2325A45000000
     

    Mitutoyo Caliper Depth Base Attachments

    Image of ProductInUse. Shown Installed. Front orientation. Caliper Depth Base Attachments. Mitutoyo Caliper Depth Base Attachments.
    Image of Product. Front orientation. Caliper Depth Base Attachments. Mitutoyo Caliper Depth Base Attachments.

    Shown Installed

    These attachments clamp onto the end of Mitutoyo electronic, dial, and vernier calipers to stabilize them when taking depth measurements.
    Mfr. Model
    No.
    For Caliper Measurement Range
    Lg.
    Wd.
    Ht.
    Slot
    Wd.
    Material
    Includes
    Each
    050083-100" to 4", 0" to 6", 0" to 8", 0 mm to 100 mm, 0 mm to 150 mm, 0 mm to 200 mm3"1/2"1 1/16"5/8"SteelScrew-Locking Clamp2325A45000000
    050085-100" to 12", 0 mm to 300 mm5"1/2"1 1/8"7/8"SteelScrew-Locking Clamp2325A4700000

    Caliper Tip Sets

    Image of ProductInUse. Shown Installed. Front orientation. Caliper Tips. Caliper Tip Sets.
    Image of Product. With Ball End, Conical, Flat, and Stem Tips. Front orientation. Caliper Tips. Caliper Tip Sets, Four Pairs of Tips (3/16" Dia. Ball End, 3/16" Dia. Conical, 3/16" Dia. Flat, 3/16" Dia. Stem).
    Image of Product. With Conical, Disk, and Stem Tips. Front orientation. Caliper Tips. Caliper Tip Sets, Three Pairs of Tips (10 mm Dia. Conical, 10 mm Dia. Disk, 2 mm Dia. Stem).

    Shown Installed

    With Ball End, Conical,

    Flat, and Stem Tips

    With Conical, Disk,

    and Stem Tips

    Attach to electronic, dial, and vernier calipers for the added versatility of measuring slots, inside pockets, shoulders, and holes.
    For Caliper Measurement Range
    Material
    Includes
    Each
    0" to 4", 0" to 6", 0" to 8"Stainless Steel
    Four Pairs of Tips (3/16" Dia. Ball End, 3/16" Dia. Conical, 3/16" Dia. Flat, 3/16" Dia. Stem)
    Hex Key Wrench
    Set Screws
    Two Tip Bodies
    20095A31000000
    0" to 6", 0" to 8", 0 mm to 150 mm, 0 mm to 200 mmStainless Steel
    Three Pairs of Tips (10 mm Dia. Conical, 10 mm Dia. Disk, 2 mm Dia. Stem)
    Hex Key Wrench
    Set Screws
    Two Tip Bodies
    20095A41000000

    Center-to-Center Measuring Caliper Tips

    Image of ProductInUse. Shown Installed. Front orientation. Caliper Tips. Center-to-Center Measuring Caliper Tips.
    Image of Product. Front orientation. Caliper Tips. Center-to-Center Measuring Caliper Tips.

    Shown Installed

    Install these tips, also known as centerline gauges, onto the jaws of electronic, dial, and vernier calipers to measure the center-to-center distance between two holes. A 60° conical shape allows the tips to fit snugly into holes.
    For Caliper Measurement
    Range
    Slot
    Wd.
    Lg.
    Material
    No. of
    Tips
    Includes
    Each
    0" to 4", 0" to 6", 0" to 8"1/8"2 5/16"Stainless Steel
    2Hex Key Wrench20415A51000000
    0" to 12"1/8"2 3/4"Stainless Steel
    2Hex Key Wrench20415A5200000

    Mitutoyo Caliper Battery Covers

    Image of Product. Front orientation. Caliper Battery Covers. Mitutoyo Caliper Battery Covers.
    Protect the battery inside your Mitutoyo caliper.
    Mfr. Model
    No.
    For Mfr. Model No.
    Material
    Each
    05CAA698500-505-10, 500-506-10Plastic2306N1300000
    05CAA738500-507-10Plastic2306N140000
    06ACQ926552-313-10, 552-314-10, 552-315-10Plastic2306N160000
    06AEG431500-170-30, 500-171-30, 500-172-30, 500-173-30, 500-193-30, 500-195-30, 500-196-30, 500-197-30, 573-291-30Plastic2306N110000
    06AEY285500-752-20, 500-753-20, 500-754-20, 500-762-20, 500-763-20, 500-764-20, 573-701-20, 573-705-20, 573-721-20, 573-761-20Plastic2306N150000
    06AEY286500-733-20, 500-734-20Plastic8647A4110000
    09GAA185500-173, 500-193, 500-196Plastic2306N120000

    Caliper Range Extenders

    Image of ProductInUse. Shown Installed. Front orientation. Caliper Range Extenders.
    Image of Product. Front orientation. Caliper Range Extenders.

    Shown Installed

    Expand electronic, dial, and vernier calipers to measure larger items. Extenders have two pins that project 1/2" when installed and act as jaws for the extension.
    Caliper Range Extender Pins—1 1/2" caliper range extender pins are sold separately.
    Caliper Range Extenders
    1 1/2"-Projection Caliper
    Range Extender Pins
    For Caliper
    Measurement Range
    Lg.
    Material
    Includes
    Each
    Dia.
    Each
    0" to 6"26"Aluminum
    6" Lg. Calibration Rod, End Block, Mounting Hardware, Set Screw, Two 1/2" Lg. Caliper Range Extender Pins85635A1100000000.62"85635A16000000
    0" to 6"36"Aluminum
    6" Lg. Calibration Rod, End Block, Mounting Hardware, Set Screw, Two 1/2" Lg. Caliper Range Extender Pins85635A120000000.62"85635A1600000
    0" to 6"51"Aluminum
    6" Lg. Calibration Rod, End Block, Mounting Hardware, Set Screw, Two 1/2" Lg. Caliper Range Extender Pins85635A130000000.62"85635A1600000
    0" to 6"71"Aluminum
    6" Lg. Calibration Rod, End Block, Mounting Hardware, Set Screw, Two 1/2" Lg. Caliper Range Extender Pins85635A170000000.62"85635A1600000
    0" to 6"91"Aluminum
    6" Lg. Calibration Rod, End Block, Mounting Hardware, Set Screw, Two 1/2" Lg. Caliper Range Extender Pins85635A180000000.62"85635A1600000
    Caliper Tips
    Caliper Tips, 0.62" Dia.—Use caliper tips to determine the center-to-center distance between holes. The tips taper to a sharp point.
    Each
    Caliper Tips, 0.62" Dia.85635A2000000

    Caliper Calibration Checkers

    Image of Product. Front orientation. Caliper Calibration Checkers.
    Check your caliper’s inside and outside measurements. These calibration checkers work with electronic, dial, and vernier calipers. They come with a certificate of calibration traceable to NIST that states they’ve passed a test for accuracy.
    Inside Size Measured
    Outside Size Measured
    Accuracy
    Material
    Container
    Type
    Each
    0.5", 1.5", 2.5", 3.5", 4.5"1", 2", 3", 4", 5", 6"-0.0002" to 0.0002"SteelCase2415A33000000000
    12.5 mm, 37.5 mm, 62.5 mm, 87.5 mm, 112.5 mm25 mm, 50 mm, 75 mm, 100 mm, 125 mm-0.005 mm to 0.005 mmSteelCase2415A3600000000

    Caliper Depth Base Attachments

    Image of ProductInUse. Shown Installed. Front orientation. Caliper Depth Base Attachments.
    Image of Product. Front orientation. Caliper Depth Base Attachments.

    Shown Installed

    Clamp onto electronic, dial, and vernier calipers to stabilize them when taking depth measurements.
    For Caliper
    Measurement Range
    Lg.
    Wd.
    Ht.
    Slot
    Wd.
    Material
    Includes
    Each
    0" to 12"2.9"0.445"1.18"5/8"Stainless Steel
    Screw-Locking Clamp8136A32000000
    0" to 12"4.9"1/2"1.37"3/4"Stainless Steel
    Screw-Locking Clamp8136A3600000

    Starrett Caliper Battery Covers

    Image of Product. Front orientation. Caliper Battery Covers. Starrett Caliper Battery Covers.
    Protect the battery inside your Starrett caliper.
    Mfr. Model
    No.
    For Mfr.
    Series
    For Mfr. Model No.
    For Caliper Measurement Range
    Material
    Each
    63620-0EC799EC799A-6/150, EC799A-8/2000" to 6", 0" to 8", 0 mm to 150 mm, 0 mm to 200 mmPlastic2260N21000000
    back to top