Anchor Type Anchor Type |
|---|
 | Stud |
 | Female Threaded |
 | Bolt |
Length Length |
|---|
|
|
|
Material Material |
|---|
|
Pull-Out Strength Pull-Out Strength |
|---|
|
Minimum Installation Depth Minimum Installation Depth |
|---|
|
|
|
Shear Strength Shear Strength |
|---|
|
|
Drill Bit Decimal Size Equivalent Drill Bit DecimalSize Equivalent |
|---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Required Installation Torque Required Installation Torque |
|---|
|
|
About Structural Adhesives
More
Vibration-Resistant Stud Anchors for Concrete
Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose. Also known as wedge anchors, the base expands as you tighten the nut for a secure hold in concrete. They're often used to anchor machinery. Made from zinc-plated steel, they resist corrosion in wet environments. Pull-out strength and shear strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Thread | Strength, lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Size | Lg. | Washer OD | Nut Wd. | Drill Bit Size | Min. Installation Dp. | Pull-Out | Shear | Tested In | Required Installation Torque, ft.-lbs. | Pkg. Qty. | Pkg. | |
Zinc-Plated Steel | |||||||||||||
1/4" Dia. | |||||||||||||
| 1 3/4" | 1/4"-20 | 1/2" | 5/8" | 7/16" | 1/4" | 1 1/8" | 370 | 500 | 4,000 psi Concrete | 8 | 6 | 000000000 | 00000 |
| 2 3/4" | 1/4"-20 | 1/2" | 5/8" | 7/16" | 1/4" | 1 1/8" | 370 | 500 | 4,000 psi Concrete | 8 | 6 | 000000000 | 00000 |
| 3" | 1/4"-20 | 1/2" | 5/8" | 7/16" | 1/4" | 1 1/8" | 370 | 500 | 4,000 psi Concrete | 8 | 6 | 000000000 | 00000 |
5/16" Dia. | |||||||||||||
| 2" | 5/16"-18 | 5/8" | 11/16" | 1/2" | 5/16" | 1 1/4" | 600 | 520 | 4,000 psi Concrete | 15 | 6 | 000000000 | 00000 |
| 3" | 5/16"-18 | 5/8" | 11/16" | 1/2" | 5/16" | 1 1/4" | 600 | 520 | 4,000 psi Concrete | 15 | 4 | 000000000 | 0000 |
3/8" Dia. | |||||||||||||
| 2" | 3/8"-16 | 3/4" | 13/16" | 9/16" | 3/8" | 1 1/2" | 820 | 1,100 | 4,000 psi Concrete | 25 | 4 | 000000000 | 0000 |
| 2 3/4" | 3/8"-16 | 3/4" | 13/16" | 9/16" | 3/8" | 1 1/2" | 820 | 1,100 | 4,000 psi Concrete | 25 | 4 | 000000000 | 00000 |
| 3 1/2" | 3/8"-16 | 3/4" | 13/16" | 9/16" | 3/8" | 1 1/2" | 820 | 1,100 | 4,000 psi Concrete | 25 | 4 | 000000000 | 00000 |
| 5" | 3/8"-16 | 3/4" | 13/16" | 9/16" | 3/8" | 1 1/2" | 820 | 1,100 | 4,000 psi Concrete | 25 | 2 | 000000000 | 0000 |
| 6" | 3/8"-16 | 3/4" | 13/16" | 9/16" | 3/8" | 1 1/2" | 820 | 1,100 | 4,000 psi Concrete | 25 | 2 | 000000000 | 0000 |
1/2" Dia. | |||||||||||||
| 2 3/4" | 1/2"-13 | 1" | 1 1/16" | 3/4" | 1/2" | 2 1/4" | 1,100 | 2,200 | 4,000 psi Concrete | 55 | 4 | 000000000 | 00000 |
| 3 1/2" | 1/2"-13 | 1" | 1 1/16" | 3/4" | 1/2" | 2 1/4" | 1,100 | 2,200 | 4,000 psi Concrete | 55 | 2 | 000000000 | 0000 |
| 5" | 1/2"-13 | 1" | 1 1/16" | 3/4" | 1/2" | 2 1/4" | 1,100 | 2,200 | 4,000 psi Concrete | 55 | 1 | 000000000 | 0000 |
| 6" | 1/2"-13 | 1" | 1 1/16" | 3/4" | 1/2" | 2 1/4" | 1,100 | 2,200 | 4,000 psi Concrete | 55 | 1 | 000000000 | 0000 |
| 7" | 1/2"-13 | 1" | 1 1/16" | 3/4" | 1/2" | 2 1/4" | 1,100 | 2,200 | 4,000 psi Concrete | 55 | 1 | 000000000 | 0000 |
5/8" Dia. | |||||||||||||
| 3 1/2" | 5/8"-11 | 1 1/4" | 1 5/16" | 15/16" | 5/8" | 3" | 2,500 | 3,200 | 4,000 psi Concrete | 95 | 1 | 000000000 | 0000 |
| 4 1/2" | 5/8"-11 | 1 1/4" | 1 5/16" | 15/16" | 5/8" | 3 1/2" | 2,500 | 3,200 | 4,000 psi Concrete | 95 | 1 | 000000000 | 0000 |
| 5" | 5/8"-11 | 1 1/4" | 1 5/16" | 15/16" | 5/8" | 3 1/2" | 2,500 | 3,200 | 4,000 psi Concrete | 95 | 1 | 000000000 | 0000 |
| 6" | 5/8"-11 | 1 1/4" | 1 5/16" | 15/16" | 5/8" | 3 1/2" | 2,500 | 3,200 | 4,000 psi Concrete | 95 | 1 | 000000000 | 0000 |
| 7" | 5/8"-11 | 1 1/4" | 1 5/16" | 15/16" | 5/8" | 3 1/2" | 2,500 | 3,200 | 4,000 psi Concrete | 95 | 1 | 000000000 | 0000 |
3/4" Dia. | |||||||||||||
| 4" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 0000 |
| 5" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 0000 |
| 6" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 00000 |
| 7" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 00000 |
| 8 1/2" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 00000 |
| 10" | 3/4"-10 | 1 1/2" | 1 1/2" | 1 1/8" | 3/4" | 3" | 3,800 | 4,500 | 4,000 psi Concrete | 170 | 1 | 000000000 | 00000 |
1" Dia. | |||||||||||||
| 10" | 1"-8 | 2" | 2" | 1 1/2" | 1" | 5 1/2" | 5,300 | Not Rated | 4,000 psi Concrete | 300 | 1 | 000000000 | 00000 |
Stainless Steel Adhesive-Grip
Female-Threaded Anchors for Concrete
These 316 stainless steel anchors have excellent resistance to chemicals and salt water and may be mildly magnetic. Use them for permanent, high-strength anchoring where vibration is present. To install, fill a clean, drilled hole half full with epoxy adhesive, then insert the anchor until it's flush with the surface. Pull-out strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Lg. | Drill Bit Size | Min. Installation Dp. | Dia. | Thread Dp. | Pull-Out Strength, lbs. | Tested In | Each | |
316 Stainless Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1/4"-20 | 1 5/8" | 5/16" | 1 3/4" | 5/16" | 1/2" | 720 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/16"-18 | 2 3/8" | 7/16" | 2 3/4" | 7/16" | 3/4" | 1,800 | 3,000 psi Concrete | 000000000 | 00000 |
| 3/8"-16 | 2 3/4" | 1/2" | 3 1/4" | 1/2" | 1" | 2,300 | 3,000 psi Concrete | 000000000 | 00000 |
| 1/2"-13 | 3 3/4" | 5/8" | 4 1/8" | 5/8" | 1" | 3,200 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/8"-11 | 5 3/4" | 7/8" | 6 1/4" | 7/8" | 1 1/2" | 6,500 | 3,000 psi Concrete | 000000000 | 00000 |
| 3/4"-10 | 6 1/2" | 1" | 7 1/2" | 1" | 1 1/2" | 9,000 | 3,000 psi Concrete | 000000000 | 00000 |
| 1"-8 | 8 1/2" | 1 1/2" | 9 1/2" | 1 1/2" | 2" | 12,700 | 3,000 psi Concrete | 000000000 | 000000 |
Steel Adhesive-Grip Female-Threaded
Anchors for Concrete
A zinc plating provides corrosion resistance in wet environments. Use these anchors for permanent, high-strength anchoring where vibration is present. To install, fill a clean, drilled hole half full with epoxy adhesive, then insert the anchor until it's flush with the surface. Pull-out strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Lg. | Drill Bit Size | Min. Installation Dp. | Dia. | Thread Dp. | Pull-Out Strength, lbs. | Tested In | Each | |
Zinc-Plated Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1/4"-20 | 1 5/8" | 5/16" | 1 3/4" | 5/16" | 1/2" | 720 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/16"-18 | 2 3/8" | 7/16" | 2 3/4" | 7/16" | 3/4" | 1,800 | 3,000 psi Concrete | 000000000 | 0000 |
| 3/8"-16 | 2 3/4" | 1/2" | 3 1/4" | 1/2" | 1" | 2,300 | 3,000 psi Concrete | 000000000 | 0000 |
| 1/2"-13 | 3 3/4" | 5/8" | 4 1/8" | 5/8" | 1" | 3,200 | 3,000 psi Concrete | 000000000 | 0000 |
| 5/8"-11 | 5 3/4" | 7/8" | 6 1/4" | 7/8" | 1 1/2" | 6,500 | 3,000 psi Concrete | 000000000 | 00000 |
| 3/4"-10 | 6 1/2" | 1" | 7 1/2" | 1" | 1 1/2" | 9,000 | 3,000 psi Concrete | 000000000 | 00000 |
| 1"-8 | 8 1/2" | 1 1/2" | 9 1/2" | 1 1/2" | 2" | 12,700 | 3,000 psi Concrete | 000000000 | 00000 |
Hex Head Removable-Bolt Anchors for Block and Brick
A hex head allows for a secure grip with a wrench. Also known as sleeve anchors, these have a sleeve that expands for a secure hold in block and brick. They're often used to hold steel and wood panels, doors, framing, and shelving. To install, tap the anchor into a hole and tighten the bolt to expand the sleeve. As you tighten, the nylon ring compresses to secure the fixture against the base material. Made from 18-8 stainless steel, they're chemical resistant and may be mildly magnetic. Pull-out strength and shear strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Thread | Strength, lbs. | Each | Package | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Size | Lg. | Head Wd. | Washer OD | Drill Bit Size | Min. Installation Dp. | Pull-Out | Shear | Tested In | Required Installation Torque, ft.-lbs. | Drive Style | For Use In | Each | Pkg. Qty. | Pkg. | ||
18-8 Stainless Steel | |||||||||||||||||
1/4" Dia. | |||||||||||||||||
| 1 3/4" | 10-24 | 3/4" | 5/16" | 0.5" | 1/4" | 1 1/4" | 370 | 520 | 4,000 psi Concrete | 3 | External Hex | Block, Brick, Concrete | 000000000 | 00000 | 4 | 000000000 | 000000 |
| 3" | 10-24 | 3/4" | 5/16" | 0.5" | 1/4" | 1 1/4" | 370 | 520 | 4,000 psi Concrete | 3 | External Hex | Block, Brick, Concrete | 000000000 | 0000 | 4 | 000000000 | 00000 |
3/8" Dia. | |||||||||||||||||
| 2 1/4" | 5/16"-18 | 7/8" | 1/2" | 0.813" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 12 | External Hex | Block, Brick, Concrete | 000000000 | 0000 | 4 | 000000000 | 00000 |
| 3 1/2" | 5/16"-18 | 7/8" | 1/2" | 0.813" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 12 | External Hex | Block, Brick, Concrete | 000000000 | 0000 | 4 | 000000000 | 00000 |
| 4" | 5/16"-18 | 7/8" | 1/2" | 0.813" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 12 | External Hex | Block, Brick, Concrete | 000000000 | 00000 | 4 | 000000000 | 00000 |
1/2" Dia. | |||||||||||||||||
| 2 3/4" | 3/8"-16 | 1" | 9/16" | 1" | 1/2" | 2 1/2" | 1,600 | 2,000 | 4,000 psi Concrete | 25 | External Hex | Block, Brick, Concrete | 000000000 | 00000 | 4 | 000000000 | 00000 |
| 4 3/4" | 3/8"-16 | 1" | 9/16" | 1" | 1/2" | 2 1/2" | 1,600 | 2,000 | 4,000 psi Concrete | 25 | External Hex | Block, Brick, Concrete | 000000000 | 00000 | 4 | 000000000 | 00000 |
Flat Head Removable-Bolt Anchors for Block and Brick
Bolts are beveled under the head for a flush finish in countersunk holes. Also known as sleeve anchors, these have a sleeve that expands for a secure hold in block and brick. They're often used to hold steel and wood panels, doors, framing, and shelving. To install, tap the anchor into a hole and tighten the bolt to expand the sleeve. As you tighten, the nylon ring compresses to secure the fixture against the base material. Made from zinc plated steel, they resist corrosion in wet environments. Pull-out strength and shear strength values are 25% of the ultimate values.
Thread | Strength, lbs. | Drive | Each | Package | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Size | Lg. | Drill Bit Size | Min. Installation Dp. | Pull-Out | Shear | Tested In | Required Installation Torque, ft.-lbs. | Size | Style | For Use In | Each | Pkg. Qty. | Pkg. | ||
Zinc-Plated Steel—Grade 5 | ||||||||||||||||
3/8" Dia. | ||||||||||||||||
| 3 3/4" | 5/16"-18 | 7/8" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 25 | 7/32" | Hex | Block, Brick, Concrete | 000000000 | 00000 | 10 | 000000000 | 000000 |
| 5" | 5/16"-18 | 7/8" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 25 | 7/32" | Hex | Block, Brick, Concrete | 000000000 | 0000 | 10 | 000000000 | 00000 |
| 6" | 5/16"-18 | 7/8" | 3/8" | 2" | 1,100 | 1,600 | 4,000 psi Concrete | 25 | 7/32" | Hex | Block, Brick, Concrete | 000000000 | 0000 | 10 | 000000000 | 00000 |
1/2" Dia. | ||||||||||||||||
| 5" | 3/8"-16 | 1" | 1/2" | 2 1/2" | 1,600 | 2,000 | 4,000 psi Concrete | 45 | 5/16" | Hex | Block, Brick, Concrete | 000000000 | 0000 | 10 | 000000000 | 00000 |
5/8" Dia. | ||||||||||||||||
| 5 1/2" | 1/2"-13 | 1 1/8" | 5/8" | 2 3/4" | 1,900 | 2,900 | 4,000 psi Concrete | 100 | 3/8" | Hex | Block, Brick, Concrete | 000000000 | 0000 | 4 | 000000000 | 00000 |
Anchoring Adhesive Kits for Concrete
Permanently set threaded rods, studs, and rebar in concrete with these kits. They include applicators and mixer nozzles to simultaneously mix and dispense the adhesive. These adhesives form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.
| Container Size, oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | For Joining | Each | |
| 5 | 5 min. @ 70° F | 45 min. | 15 in 9/16" dia. hole | 10,900 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | Masonry | 00000000 | 000000 |
| 8.6 | 20 min. @ 75° F | 24 hrs. | 12 in 5/8" dia. hole | 8,600 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 15,300 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 22,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 35,000 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 43,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 47,000 lbs.—1" threaded rod dia. × 9" installation dp. 67,200 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 1:1 | Paste | 40° to 110° | Gray | Masonry | 000000000 | 000000 |
| Replacement Mixer Nozzle for 5-oz. Kit | 00000000 | Each | 00000 |
High-Temperature Anchoring Adhesives for Concrete
These adhesives maintain their strength in temperatures up to 250° F. Use them to permanently set threaded rods, studs, and rebar in concrete. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.
Use the included mixer nozzle and a dispensing gun (sold separately) to simultaneously mix and dispense adhesive.
| Container Size, oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 27.9 | 3 min. @ 70° F | 30 min. | 85 in 9/16'' dia. hole | 10,500 lbs.—3/8" Threaded Rod Dia. × 3 3/8" Installation Dp. 16,900 lbs.—1/2" Threaded Rod Dia. × 4 1/2" Installation Dp. 22,700 lbs.—5/8" Threaded Rod Dia. × 5 5/8" Installation Dp. 28,300 lbs.—3/4" Threaded Rod Dia. × 6 3/4" Installation Dp. 29,600 lbs.—7/8" Threaded Rod Dia. × 7 7/8" Installation Dp. 44,200 lbs.—1" Threaded Rod Dia. × 9" Installation Dp. 68,000 lbs.—1 1/4" Threaded Rod Dia. × 11 1/4" Installation Dp. | 10:1 | Paste | 25° to 250° | Gray | 0000000 | 000000 |
Anchoring Adhesives for Concrete
Permanently set threaded rods, studs, and rebar in dry concrete with these two-part epoxies. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. The size listed is the combined total of the two parts. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.
Adhesives in cartridges can also be used in damp concrete. Use a mixer nozzle and dispensing gun (dispensing gun sold separately) to simultaneously mix and dispense adhesive.
Adhesives in pails have epoxy and hardener in separate containers that can be mixed in the pail.
| Container Size, oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 8.5 | 5 min. @ 40° F | 48 hrs. | 14 in 5/8" dia. hole | 8,600 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 15,300 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 22,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 35,000 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 43,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 47,000 lbs.—1" threaded rod dia. × 9" installation dp. 67,200 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 1:1 | Paste | 50° to 110° | Teal | 000000 | 000000 |
| 8.6 | 20 min. @ 75° F | 24 hrs. | 12 in 5/8" dia. hole | 8,600 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 15,300 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 22,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 35,000 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 43,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 47,000 lbs.—1" threaded rod dia. × 9" installation dp. 67,200 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 1:1 | Paste | 40° to 110° | Gray | 000000000 | 00000 |
| 10.1 | 9 min. @ 60° F | 1 hrs. | 25 in 9/16" dia. hole | 7,000 lbs.—3/8" threaded rod dia. × 3 3/8" installation dp. 13,000 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 16,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 22,000 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 32,000 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 41,000 lbs.—1" threaded rod dia. × 9" installation dp. | 10:1 | Gel | 15° to 145° | Gray | 0000000 | 00000 |
| 22 | 5 min. @ 60° F | 24 hrs. | 35 in 5/8" dia. hole | 8,600 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 15,300 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 22,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 35,000 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 43,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 47,000 lbs.—1" threaded rod dia. × 9" installation dp. 67,200 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 1:1 | Paste | 50° to 110° | Gray | 0000000 | 00000 |
| Dispensing Gun for 8.6-oz. Cartridges | 000000000 | Each | 000000 |
| Mixer Nozzle for 8.6-oz. Cartridges | 000000000 | Each | 0000 |
| Mixer Nozzle for 8.5-oz. and 22-oz. Cartridges | 0000000 | Each | 0000 |
| Dispensing Gun for 22-oz. Cartridges | 0000000 | Each | 000000 |
| Dispensing Gun for 8.5-oz Cartridges | 0000000 | Each | 00000 |
| Mixer Nozzle for 10.1-oz. Cartridges | 0000000 | Each | 0000 |
| Dispensing Gun for 10.1-oz Cartridges | 0000000 | Each | 00000 |
| Container Size, gal. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 2 | 30 min. @ 75° F | 24 hrs. | 100 in 1" dia. hole | Not Rated | 2:1 | Paste | 50° to 110° | Gray | 0000000 | 000000 |
| 5 | 30 min. @ 75° F | 24 hrs. | 500 in 1" dia. hole | Not Rated | 2:1 | Paste | 50° to 110° | Gray | 0000000 | 000000 |
Submersible Anchoring Adhesives for Concrete
When concrete is saturated with or submerged in water, use these epoxies to permanently set threaded rods, studs, and rebar. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities. Use a mixer nozzle and dispensing gun (dispensing gun sold separately) to simultaneously mix and dispense adhesive.
| Container Size, oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 8.6 | 20 min. @ 75° F | 4 hrs. | 20 in 9/16'' dia. hole | 9,200 lbs.—3/8" Threaded Rod Dia. × 3 3/8" Installation Dp. 22,300 lbs.—1/2" Threaded Rod Dia. × 4 1/2" Installation Dp. 29,900 lbs.—5/8" Threaded Rod Dia. × 5 5/8" Installation Dp. 39,200 lbs.—3/4" Threaded Rod Dia. × 6 3/4" Installation Dp. 53,800 lbs.—7/8" Threaded Rod Dia. × 7 7/8" Installation Dp. 62,900 lbs.—1" Threaded Rod Dia. × 9" Installation Dp. 88,500 lbs.—1 1/4" Threaded Rod Dia. × 11 1/4" Installation Dp. | 1:1 | Paste | 35° to 110° | Gray | 0000000 | 000000 |
| 9.5 | 5 min. @ 70° F | 45 min. | 25 in 9/16" dia. hole | 10,900 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 00000 |
| 20.7 | 20 min. @ 75° F | 4 hrs. | 48 in 9/16'' dia. hole | 9,200 lbs.—3/8" Threaded Rod Dia. × 3 3/8" Installation Dp. 22,300 lbs.—1/2" Threaded Rod Dia. × 4 1/2" Installation Dp. 29,900 lbs.—5/8" Threaded Rod Dia. × 5 5/8" Installation Dp. 39,200 lbs.—3/4" Threaded Rod Dia. × 6 3/4" Installation Dp. 53,800 lbs.—7/8" Threaded Rod Dia. × 7 7/8" Installation Dp. 62,900 lbs.—1" Threaded Rod Dia. × 9" Installation Dp. 88,500 lbs.—1 1/4" Threaded Rod Dia. × 11 1/4" Installation Dp. | 1:1 | Paste | 35° to 110° | Gray | 0000000 | 00000 |
| 28 | 5 min. @ 70° F | 45 min. | 75 in 9/16" dia. hole | 10,900 lbs. —3/8" Threaded Rod Dia. × 3 3/8" Insulation Dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 00000 |
| Replacement Mixer Nozzle for 28-oz. Cartridges | 0000000 | Each | 00000 |
| Dispensing Gun for 28-oz. Cartridges | 0000000 | Each | 000000 |
| Dispensing Gun for 8.6-oz. Cartridges | 0000000 | Each | 00000 |
| Replacement Mixer Nozzle for 8.6-oz. Cartridges | 000000000 | Each | 0000 |
| Dispensing Gun for 20.7-oz. Cartridges | 0000000 | Each | 000000 |
| Replacement Mixer Nozzle for 20.7-oz. Cartridges | 000000000 | Each | 0000 |
| Replacement Mixer Nozzle for 9.5-oz. Cartridges | 00000000 | Each | 0000 |
| Dispensing Gun for 9.5-oz. Cartridges | 0000000 | Each | 00000 |
Structural Support Epoxies for Heavy Machinery
Fill the void beneath motors, pumps, and other large machinery to create a structural support for your equipment. Also known as chocking epoxies, these epoxies replace traditional metal chocks, which often need to be machined. Mix these two-part epoxies and pour them in between your equipment and your base—they flow into every nook and cranny for a strong, long-lasting bond. As these epoxies cure, they won’t shrink. Designed to withstand demanding environments, these epoxies handle heavy loads, vibration, and chemicals without cracking. Especially good for harsh marine applications, you can use them when installing marine engines and deck-supported equipment, such as hoists and winches.
Container | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, lbs. | Type | Consistency | Viscosity, cP | Color | Begins to Harden, min. | Reaches Full Strength, hrs. | Approx. Coverage @ Thick. | Mix Ratio | Temp. Range, °F | Each | |
Loctite® PC 7202 | |||||||||||
| 7 | Can | Thick Liquid | 15,000 | Orange | 10 | 24 | 123.2 sq. in. @ 1" | 100:11.6 | -20° to 250° | 000000000 | 0000000 |
| 21 1/2 | Pail | Thick Liquid | 15,000 | Orange | 10 | 24 | 378.4 sq. in. @ 1" | 100:11.6 | -20° to 250° | 000000000 | 000000 |