Update standard outlet boxes in closets, hallways, and storage rooms to use LED light.

Fit traditional fluorescent ceiling strip lights with LED lights, which use less electricity.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Don’t waste energy lighting unoccupied spaces—these lights turn on when they detect movement.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

No need for wiring—these lights plug into a standard wall outlet. Also known as shop lights.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Brighten large, open areas, such as warehouses and manufacturing spaces. IP rated and UL listed for wet locations, these lights are sealed against washdowns.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Create ambient and accent lighting with these sleek, modern lights that shine above, below, and around themselves.

Illuminate harsh, wet areas, even outside in extreme weather—these lights are often used on ship building ports. Rated NEMA 4X and UL marine listed, they’re sealed against heavy rain and washdowns, and they won’t corrode from salt water or other liquids.

Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Also known as sconces, these lights are a stylish choice for ambient and accent lighting in hallways and entryways. They’re UL or ETL listed for wet locations, so you can install them outdoors—rain and humidity won’t be a problem.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Upgrade your existing hazardous location bay lights to energy-efficient LEDs.

Illuminate chemical plants, refineries, and other facilities where flammable and combustible gases may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

The enclosure on these jelly jar lights contains explosions, sparks, and flashes. These lights are safe to use in NEC Class I, II, and III, Division 1 hazardous locations.

Mount these lights in large, open areas where flammable and combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Also known as drip caps, these lights have a rounded housing that diverts rain and snow away from your doorframe. Mount them above entrances to light the way and keep water from trickling inside.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Hardwire these lights to a power source.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Startle intruders and draw attention to activity in remote areas without access to power—these solar-powered lights shine bright when motion is detected. They charge during the day, and the battery lasts all night with typical activity.

Heads adjust to any angle so you can direct light where needed.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

With built-in LEDs, these lights deliver all the brightness of larger dock lights in a low-profile design. A hinge stop keeps the arm from extending past the dock door, and the curved design fits around the track.

When the power goes out, these lights turn on. They have adjustable heads that illuminate the path toward exits during outages.

Installed in drop ceilings, these lights are often used in open workspaces where columns and walls are few and far between. Unlike traditional backup lights, they don’t require a vertical surface for mounting.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.