This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Remove water in locations without power with these battery-operated pumps.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job.

Pumps have a powerful motor that provides more than twice the flow rate of standard water-removal pumps to quickly remove large volumes of liquid. They activate when plugged in; add a float switch to control when the pump activates.

Fill the fuel tank with gasoline to remove water at sites without power.

With a polypropylene housing, these pumps are about half the weight of other gasoline-powered pumps. Fill the fuel tank with gasoline to remove water at sites without power.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2” in diameter.

The float switch is wired to the pump. Use with debris-free water.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Use with debris-free water.

Since the switch activates on increasing pressure caused by rising water levels, these pumps have no external moving parts to catch on sump pit walls. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

Convenient for applications where a sump pit is impractical, these pumps include a basin. Use with debris-free water.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

These pumps provide over 50% more flow than standard plug-in activated pumps for sewage water. They activate when plugged in. You can add a plug-in switch to control when the pump activates. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

Equipped with a large intake and a rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. Pumps transfer raw sewage water with solids up to 2” in diameter.

Use these pumps to move higher volumes of water with solids than other sump pumps. They activate when plugged in; add a plug-in switch to control when the pump activates. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed

The float switch has a separate cord that can unplug, so you can repair the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

If the primary float fails, the backup float kicks in and an alarm sounds to indicate float malfunction.

Hang these switches in a sump pit to detect rising water levels.

These unthreaded rubber strainers fit onto 3/4 NPT male connections.

Place your pump inside these basins for ground-level applications and below-ground use without a sump pit.

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

Also known as gear pumps, these produce a smooth flow of liquid for applications such as cooling engines, powering hydraulic equipment, and extracting liquid from holding tanks.

Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

These pumps have a bronze housing and gears for use with water. Also known as gear pumps, they produce a smooth flow of liquid for water delivery.

Also known as plunger pumps, these can provide pressures up to 3,000 psi. Use them for washdowns, drain jetting, and other pressurized water-spraying applications.

Also known as flexible impeller pumps, these create a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.