Squeeze the handles and the jaws will automatically adjust to fit your workpiece.

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

The jaws on these tools apply outward pressure for use as a spreader.

The long, pivoting jaws let you clamp farther into your workpiece and in tight spots.

Press the lever to lock the clamp onto material.

These clamps meet DIN VDE 0680-1 for protection against accidental contact with live electrical circuits.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Extend the handle to reach the clamp into tight spaces.

Clamp thin sheet material together without drilling holes. These clamps open with special pliers and spring closed when the pliers are released.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Push the lever to lock the handle and prevent accidental opening.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Mount these clamps below a surface.

The mounting base secures these clamps to a rail or bar.

These clamps have mounting holes on the bottom.

Mount the base to a work surface using screws.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

Two clamps connected by a pivoting arm hold workpieces at nearly any angle.

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

These clamps have twice the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Pull the lever to slide the clamping arm along the bar; release to lock in place.

All adjustments can be made from one end, allowing clamping in tight spaces.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.

Grip all four corners of a rectangular workpiece.

Apply pressure to the side of a workpiece as well as the top and bottom.

Plastic clamping surfaces prevent damage to material.

With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.

Lighter weight than other metal clamps, these are less likely to bend thin material.

Plastic clamping surfaces prevent damage to material.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Clamp farther in from the edge of a workpiece than with other C-clamps.

With no handle or protruding screw, these clamps can fit into tight spaces.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Hold workpieces of different thicknesses without adjustment.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Push the lever to lock the handle and prevent accidental opening.

Secure these clamps to a rail or bar.

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

The open clamp design permits welding around almost the entire pipe circumference. A combination of chains and support bars hold a variety of pipe sizes.

Fit the draw arm over a latch plate and pull the handle to clamp.

Mount the clamp on a lid and the latch plate on the side of a container.

Get everything needed for basic workholding on a machine table.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.

The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Mount using the holes in the base.

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

Insert these clamps into drilled holes in sheet material to grip and align when riveting or welding.

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

When there isn't clearance to use standard-grip locking pliers, the angled handle on these tools gives you access. Lock the jaws around a workpiece and these pliers stay clamped in place.

Hold larger workpieces than standard locking pliers. These tools lock in a vise-like grip around a workpiece and stay clamped in place.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Lock the jaws around a workpiece and they stay clamped in a vise-like grip.

Change out worn or broken springs in the handle of your locking pliers.

Curved jaws grip bolt heads and nuts with rounded corners. These pliers lock in a vise-like grip and stay clamped in place, leaving your hands free.

Attach your locking pliers to a slide hammer to pull stubborn objects.