A sealed lens keeps moisture out to protect these lights against washdowns.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

These lights produce a wide beam of uniform light to fill large, open areas with ceilings up to 18-ft. high.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Powered by the sun, these lights illuminate outbuildings, shipping containers, and other remote places that lack electricity.

No need for wiring—these lights plug into a standard wall outlet. Also known as shop lights.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Use these lights in large, open areas such as warehouses and manufacturing spaces where the ceiling is up to 30-ft. high.

These lights mount to the wall so they're often used in enclosed spaces such as stairwells, hallways, and storage rooms.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

Update conventional fluorescent tubular lights with newer LED technology. These lights are furnished with brackets that have the same hole pattern as most older lights for easy changeover.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Mount these lights near entry doors, loading areas, and driveways to cast an even glow of light.

Heads adjust to any angle so you can direct light where needed.

Hardwire these lights to a power source.

No need for wiring—these lights plug-in with a three-prong plug.

These lights automatically turn on when movement is detected and off when an area is unoccupied.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

Our brightest plug-in floodlights, these lights illuminate large worksites—about the size of a hockey rink.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

With built-in LEDs, these lights deliver all the brightness of larger dock lights in a low-profile design. A hinge stop keeps the arm from extending past the dock door, and the curved design fits around the track.

These lights are sealed to protect against humidity, moisture, and dripping and splashing liquids.

Mount add-on heads in remote areas to extend emergency lighting.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.