A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Keep material from coming in contact with the mounting surface without the need for a spacer.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.