The grips are a fluorescent color to stand out.

The grips on these cutters drain static from your application, preventing buildup from electrostatic discharge (ESD).

These cutters are stainless steel, which provides excellent corrosion resistance.

Plastic-cushioned grips make these cutters easy to hold during repeated cuts.

Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Cut thin, hard wire with these small cutters.

Cutters have double hinge that provides high cutting force with low gripping pressure.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

These manually operated cutters make a clean cut with just a few pumps of the handle.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Cut hard bolts and up to Grade 70 chain with reinforced blades that stay aligned during repeat cuts.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Slice through bolts and chain with low effort.

Jaws ratchet to increase cutting pressure as you open and close the handles.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Cut armored cable such as BX, HCF, and MC and flexible metal conduit.

Keep your hand away from the material being cut.

The handles are angled 90° from the blade so you can cut material from directly above tight spaces.

Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.

These cutters make straight cuts and curves.

Replace blades as they wear. These cutters are also known as tinners' snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.

Leave clean cut edges in a variety of pliable materials.

Also known as electricians' shears, the back edge of the blade has a file to clean contacts.

With high-carbon stainless steel blades, these scissors cut through fiber-optic and electrical cables, even those that are made with Kevlar. They’re also good for cutting wire jackets and cable ties.

These small scissors have narrow, sharp tips for fine cutting and trimming

Minimize hand fatigue with a lightweight handle and spring-action that automatically opens the blades for quick repeat cuts.

Longer handles and shorter blades give you more leverage than other scissors to cut tough materials such as leather, rope, and thick cardboard.

Blades are ceramic to stay sharp longer than metal blades.

After each cut, the jaws spring open to make continuous cutting easy.

Jaws open automatically for ease of use.

The head slides out of the handle and locks in position.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use them to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height. Use these tools to pull, bend, and cut wire.

The grips drain static from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

Insulated grips protect against accidental contact with live electrical circuits. These assorted pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Smooth, consistent movement ensures precision. These assorted pliers have slip-resistant ultra grips that are shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

Additional features, such as wire terminal crimpers and wire stripping holes, enable you to perform a variety of electrical wiring and installation work with a single tool.

Tips almost twice as wide as those of standard long-nose pliers give you a better grip on your work. These are also known as duckbill and flat-nose pliers.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Made of materials that are FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pull stripped, rusted, and tamper-resistant screws out of hard-to-reach places.

Squeeze the handles and the jaws automatically adjust to fit a workpiece and lock in place.

Curved jaws grip bolt heads and nuts with rounded corners. These pliers lock in a vise-like grip and stay clamped in place, leaving your hands free.