The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

No need to pull the socket off the tool—push a button to release.

Bolts and threaded rod pass through these wrenches when used with bolt-through sockets.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

Extend the shaft for additional length.

Position the head anywhere along the handle.

Turn sockets from above when there's not room to swing a standard wrench handle.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

Measure with an accuracy of ±2%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Anchor these multipliers for added stability.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Use these tools for general shop applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These short sockets fit spaces where height clearance is limited.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

For easy tightening and loosening, these sockets have pins that grip the slotted sides on bearing nuts.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

These sockets fit the nuts found on water and gas valves.

Designed to fit on external Torx-Plus fasteners, often found on pickup trucks, these sockets have squared lobes that resist slipping at high torque.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

These sockets are also known as Robertson bits.

Pivot the head to access fasteners from an angle.

A magnet holds the fastener securely enough to drive self-tapping screws.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Tighten or loosen nuts and bolts without damaging the finish.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Quickly position these sockets on square fasteners.

The square shape provides the best possible grip on square fasteners and prevents rounding.

Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.

The hex shape grips hex fasteners and prevents rounding.

For high quality at a lower price, choose these U.S.A.-made sets.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pivot the head to access fasteners from an angle.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.

Grip the indentations around the outside of tri-groove fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Lock your socket into the extension to prevent accidental disengagement..

Pivot the head to access fasteners from an angle.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Attach to your socket for a longer reach.

Remove and install dual wheels on trucks and trailers with the sockets in these sets.