Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

A reliable classic—these babbitt bearings are strong and corrosion resistant.

With no moving parts, sleeve bearings are better for dirty environments than ball and roller bearings.

The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings.

Keep these shaft collars in place by tightening their set screw into the shaft.

Internal ball bearings allow you to slide a collar onto your shaft in one direction and then automatically lock the collar in place in the opposite direction.

With a nylon insert that grips your threaded shaft or spindle without damaging its threads, these locknuts—also called shaft nuts—hold bearings, bushings, gears, and pulleys prone to vibration tightly in place.

Each hub includes a set screw (unless noted), which bites into your shaft to hold the coupling in place.

A flexible tire on these couplings safeguards components on your shafts by reducing vibration and shock.

For use with splined shafts, which are commonly found in gearboxes and pumps, these couplings are capable of transmitting more torque than couplings for round and keyed shafts.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

The zinc plating provides some corrosion resistance.

An economical alternative to standard unthreaded spacers.

A smooth base provides more contact with the mating surface than weld nuts with projections.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

A hex-shaped body provides the highest twist resistance of any rivet nut.

About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.

The thread area is enclosed, which prevents leakage past the threads from either side of your application.

The through hole allows you to connect float rods to float valves.

These inserts cut their own threads in soft metals such as aluminum, so there's no need to tap the hole. Also known as Tap-Lok inserts.

Steel inserts have high strength for durability.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

A zinc-plated finish gives these steel inserts mild corrosion resistance.

These rivet nuts have a smooth body and fit in smaller holes than twist-resistant rivet nuts. Assortments include rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Use these corrosion-resistant fittings in a low-pressure pipe line.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

Used in low-pressure pipe lines, these brass fittings have a plating that makes them shiny and improves corrosion resistance.

Not only do these brass fittings have the strength to handle high-pressure applications, the male threads have a sealant applied for extra protection against leaks.

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

Extreme pressures are no problem for these heavy-duty brass fittings.

Use these fittings for low-pressure applications in noncorrosive environments.

The male threads on these fittings have a sealant applied for extra leak protection.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Designed for medium-pressure applications, these fittings have better strength than our low-pressure aluminum pipe fittings.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications up to 200° F.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

Use these plastic fittings to connect gasoline fuel lines to machines and equipment. They have excellent corrosion resistance as well as high strength and impact resistance.

Fittings meet NSF/ANSI Standard 61 for drinking water. Attach them to garden hose for a variety of water supply applications. They are metal for better durability than plastic garden hose fittings.

These nuts attach to high-pressure nipples for compressed gas so you can connect your tank to the inlet of a pressure regulator.

Connect to the end of conduit or a fitting to protect wires from abrasion when being pulled.

Join pieces of conduit.

Connect different sizes of conduit.

These grips are sized to fit in tight areas.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.