Use these end mills for short runs and general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

Commonly used to make keyways in rotary shafts, these tools have a -0.0015" to 0.0000" mill diameter tolerance for creating a precise fit.

For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills.

A 45° corner chamfer improves cutting edge strength, so these end mills last longer than standard square end mills when milling hard material; however they do not create as sharp of a corner. Variable spacing between the flutes reduces vibration, allowing them to provide fast cuts, smooth finishes, and long tool life.

Intersecting flutes create a fine finish, making these end mills good for operations requiring light stock removal, such as deburring, profiling, and finishing.

Remove large amounts of material quickly without sacrificing tool life. These end mills have serrations on the cutting edge and variable spacing between flutes to reduce cutting time and vibration in high-volume jobs.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

With a wear-resistant coating and high helix angle, these end mills provide excellent shearing and chip removal in stainless steel and titanium.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a high helix angle and a wear-resistant coating for excellent shearing and chip removal in stainless steel and titanium.

Three high-helix-angle flutes provide a smooth finish on nickel alloys, such as Monel, Inconel, and Hastelloy.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as cast iron, hardened steel, titanium, and tool steel.

A higher helix angle means these end mills clear more chips than other roughing cobalt steel end mills, making them better for milling aluminum, brass, and bronze. Serrations along the cutting edge act as chip breakers, so they can remove large amounts of material at high speeds.

Use these tools with low-horsepower, manual milling machines. They have clamps for holding inserts that do not have a mounting hole. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

Fasten carbide inserts directly to these end mills for a hold that's strong enough to handle the high speeds of a CNC machine. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than cobalt steel for the longest life and best finish on hard material. A 90° pointed tip allows them to be used for drilling as well as for slotting, profiling, chamfering, and spotting cuts.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their angled profile allows chamfer, bevel, and other angled cuts.

These carbide-tipped end mills provide a sharper, harder cutting edge and better wear resistance than high-speed steel without the brittleness of solid carbide. Their teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.

In a single pass, these tools mill a precise, angled finish on the outside edge of pipe, tubes, and rods. Use them to deburr pipe and tube for butt welds or to shape rods and shafts for sliding into housings and holes. Faster and more precise than handheld scrapers, they work with screw machines, lathes, and drill presses to make reliable cuts, part after part.

Use these end mills for general purpose keyseat cutting in a wide range of material, including aluminum, iron, and steel. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

With better heat and wear resistance than high-speed steel, these cobalt steel keyseat cutters can run at higher speeds and provide better performance on hard material. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

Create dovetail grooves that allow O-rings to flex without falling out of place.

With better heat and wear resistance than high-speed steel, these cobalt steel dovetail cutters run at higher speeds and provide better performance on hard material. Use them to create dovetail slots for connecting two components with a sliding fit.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They're often used to create slots in machine tool tables, indexing tables, and other workholding surfaces.

Flutes have a low helix angle to provide the cutting forces required for difficult-to-machine material, such as tool steel, hardened steel, and iron.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. Made of solid carbide, they are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

Use these end mills for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

When one end wears out, switch to the opposite end for two times the life of a standard high-speed steel end mill. Made of high-speed steel, these end mills are for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills run at higher speeds and provide better performance on hard material. They have scooped corners for rounding the sharp edges of your workpiece.

When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Use them to round sharp corners on the edge of your workpiece.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. With curved, side-cutting teeth, they create hollow, inward-curving grooves.

With a wear-resistant coating and high helix angle, these end mills provide excellent shearing and chip removal in stainless steel and titanium. Often used for slotting and pocketing cuts in mold and die making, these end mills have a 90° profile and rounded corners, which reduce flute breakage and chipping.

Made of cobalt steel, these end mills have good heat and wear resistance, so they can run at high speeds in hard material. Often used for slotting and pocketing cuts in mold and die making, they have a 90° profile and rounded corners, which reduce flute breakage and chipping.

Also known as shell cutters, these high-speed steel cutters are good for face and side milling. They have a large mill diameter for removing a large amount of material per pass.

These kits include a cutter body, inserts, wrenches, and screws, so you can create your own face milling cutters, which are also known as indexable face milling cutters.

With peripheral and side teeth, these cutters remove chips for a consistent cutting width.

Made of solid carbide, these cutters are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material. Use them for cutoff, slitting, and slotting applications.

For general purpose milling in most material, the end mills in these sets have one milling end and a standard shank.

Offering two times the life of a standard end mill, these have two milling ends so you can switch to the opposite end when one end wears out. Use them for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

Also known as fly cutters, these clamp onto tool blanks to machine flat surfaces. As the cutter rotates, the tool blank creates a wide, shallow cut on the face of the workpiece.

Offering two times the life of a standard carbide end mill, the end mills in these sets have two milling ends so you can switch to the opposite end when one end wears out. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

Attach to the quill of your milling machine to accurately set machining depth. The spring-loaded design allows you to squeeze the knobs toward each other, so you can make adjustments with one hand. Also known as quill stops.

Clear chips and shavings from machine tables and trays. Hooks are steel and have a plastic guard to protect your hand from cuts and splinters.

Increase precision and prolong the life of your tooling by cleaning out chips, dust, and coolant from your machine's tapered spindle.

Replace worn drawbars in Bridgeport, Lagun, Wells, and other milling machines.