Nickel plating gives these magnets good corrosion resistance.

In addition to protecting magnets and mounting surfaces, a rubber coating gives these magnets a slip-resistant surface.

Many small poles give these magnets shallower, more concentrated magnetic fields that hold especially well on thin material. They resist temperatures up to 180° F.

These magnets have a central hole for mounting on shafts. Use them in motors and turbine generators.

Made of neodymium, these rare earth magnets are the strongest for their size. Slide onto a rod or use a bolt or screw to install.

Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 400° F.

A metal case protects the magnetic material.

A smooth metal cover gives these magnets a finished appearance.

Alnico magnets resist temperatures up to 420° F.

A rubber cover protects the magnet and mounting surface.

A metal case protects the magnetic material.

These ceramic magnets resist demagnetization better than other magnets, and have a metal case to protect the magnetic material. They resist temperatures up to 175° or 245° F.

To add a magnetic surface anywhere, install the mounting plate, then screw on the magnet.

A plastic case protects the mounting surface as well as the magnet.

These magnets are made of corrosion-resistant ceramic and bonded with rubber for flexibility.

Stretch these magnetic strips over corners and irregular surfaces.

Position the face of these magnets in direct contact with a flat metal surface and turn on the power to create a magnetic hold.

Plug in these electromagnets to create a magnetic hold. A transformer in the plug converts power from AC to DC, so no additional wiring or power source is needed.

Turn the handle to switch these magnets on and off.

These magnets are bonded with epoxy resin, so they can be machined with carbide tooling.

Attach parts in the same place every time with these magnet pairs that center as they pull together.

Pick up screws, nuts, and other small steel objects.

An extra-long shaft enables access to material in hard-to-reach areas. These retrievers can pick up heavier objects than our other magnetic retrievers.

Often used to pick up steel sheets, the magnet holds material until you press the lever to disengage it.

LEDs light the magnetized tip and the shaft bends and stays in position to reach objects in awkward spaces.

Protect against accidental contact with live electrical circuits. These insulated retrievers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. The shaft bends and stays in position to reach objects in awkward spaces.

Two clamps connected by a pivoting arm hold workpieces at nearly any angle.

Each arm has a handle for turning the magnets on and off.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

Sets include a handle and an assortment of tips for holding and positioning wire, springs, and other small parts.

The entire surface of these plates is magnetic to provide a powerful hold for grinding, drilling, and electrical discharge machining (EDM). Pull the handle to switch the magnets on and off.

Attach these general purpose hooks to steel walls, cabinets, and other magnetic surfaces.

Store tools such as brooms, screwdrivers, and flashlights with these holders that attach to magnetic surfaces.

Keep instructions and safety sheets on any magnetic surface, such as a steel cabinet, desk, or machine.

Hold steel tools, nails, nuts, screws, and other magnetic items on your pegboard.

These holders keep steel tools and knives in place magentically.

Slip these pouches onto your belt to keep several tools within reach.

Magnetic force holds doors closed.

Made to NSF/ANSI standards, these latches have a completely sealed magnet to eliminate crevices that can trap food particles.

Close and open these magnetic latches with a push—there's no need for a handle.

These locks use electromagnetic force to hold double doors closed, often as part of an access-control system.

Secure doors and windows made of T-slotted framing to protect valuables or restrict access for safety.

An on/off magnet control makes it easy to move and attach these brackets to metal surfaces.

For use with doors that already have a closer, these holders keep doors open with an electromagnet. When activated by a fire alarm, the magnet shuts off and releases the door.

Easily grab iron and steel fasteners, small sheets, and other parts from work areas, bins, and hard-to-reach places.

A long handle gives you the leverage to safely remove manhole covers by yourself.

These magnets hold a load until you pull the handle and pry the magnet off.

Separate stacked steel sheets without prying, scratching, or bending them.

These filters are designed without guide rods to prevent wet and sticky material from blocking flow.

The guide rods direct flow to the magnetic rods. They’re helpful in removing dry particles from fine powder and low-flow applications.

Pull the rods from their sleeve to release particles stuck to the filter.

These filters are designed without guide rods to prevent wet and sticky material from blocking flow.

A quick-release feature lets you clean these sweepers without touching debris.