We will reply to your message within an hour.
More
Use this general purpose tubing to insulate and protect wire and cable.
Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.
This tubing creates a tight seal over irregularly shaped objects.
The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.
Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.
Identify ground wire with this green-and-yellow striped tubing.
Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.
This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.
Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.
Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.
This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.
With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.
With excellent resistance to tears and cuts, this tubing withstands demanding use.
Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.
Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.
Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.
Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.
Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.
Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.
A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.
Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.
Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.
Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 5,000 volts.
A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.
After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.
Keep general purpose tubing in a variety of sizes on hand.
Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.
A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.
Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.
Seal the end of crimped connections, such as motor coils, to protect them from moisture.
Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.
Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this wrap has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.
Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.
Apply heat and these grommets shrink around wire, cable, and cords to keep out dust, debris, and moisture.