The orbital motion produces more consistent finishes than standard disc sanders. Also known as random orbital sanders.

These sanders move in a rotary motion.

The orbital motion produces consistent finishes. Also known as random orbital sanders.

The narrow belt is good for sanding in tight spaces.

These sanders are mounted on a 100 cfm dust collector. Operate in a horizontal or vertical position.

Operate in a horizontal position, vertical position, or any angle in between.

Keep hands safely out of the way while deburring, sanding, and polishing workpieces on a lathe.

The small triangular pad reaches into tight corners and spaces.

Use with 6" x 9" pads.

Blocks hold an adhesive-back sanding roll—cut off worn abrasive and pull out more as needed.

These rubber blocks sand flat surfaces.

Attach a 1" wide sanding sheet to create your own file.

Secure the shank into the collet or chuck of your tool.

Various sizes and grits of flap sanding wheels are included in these assortments. Secure the shank into the collet or chuck of your tool.

An additive in the abrasive resists heat.

These assortments include various sizes and grits of flap sanding wheels. The threaded stud allows faster wheel changes but requires the use of an adapter in your tool.

The premium abrasive stays sharp longer.

A coating prevents dust and debris from building up on the abrasive surface.

Fit these wheels over your tool's arbor. The flexible flaps reduce gouging while producing a uniform finish on flat and curved surfaces.

Assortments include a selection of flap wheels to polish, clean, and deburr deep inside tubes and cylinders.

With alternating cloth and nylon mesh abrasive flaps, these wheels are more flexible and produce finer finishes than all-cloth flap wheels.

Thicker, more pliable, and less aggressive than standard nylon mesh quick-change discs, use these for finer sanding on curved surfaces.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a harder abrasive than standard quick-change discs.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

The premium abrasive stays sharp longer.

Used for heavy cleaning and stripping, these discs have an abrasive-embedded nylon mesh construction that gives you more control over sanding pressure.

The heavy duty construction provides more support than standard discs for heavy material removal.

These discs are abrasive-embedded cloth with a cushioned layer.

Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.

Holes allow dust removal when used with a vacuum sander.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

Holes allow dust removal when used with a vacuum sander.

Fit these discs over your tool's arbor.

A coating prevents dust and debris from building up on the abrasive surface.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Used for stripping, these discs eliminate discoloration from heat buildup.

Fit these discs over your tool’s arbor to sand stainless steel and hard metals.

A coating prevents dust and debris from building up on the abrasive surface.

Fit these discs over your tool's arbor to sand masonry, ceramics, and composites.

With more flaps than standard discs, these last 30-40% longer.

With more flaps than standard discs, these last 30-40% longer.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

These discs have a harder abrasive than standard flap sanding discs.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

With more flaps than standard discs, these last 30-40% longer.

Set at an angle and widely spaced, the flaps reach into corners.

Use with commercial floor buffing machines to sand wood floors and strip tape from concrete.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

A coating prevents dust and debris from building up on the abrasive surface.

Evenly sand two surfaces at once.

Keep sanding sheets of various grits on hand.

A selection of 40 emery and crocus sanding sheets are included in these assortments.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

These rolls can be cut to length.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

The soft abrasive is good for fine hand-polishing of soft nonferrous metals. Also known as crocus cloth.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Keep an assortment of sheets that prevent dust and debris from building up on the abrasive surface close at hand.

A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface. These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

The dental floss of abrasives, these cords slip into areas that other forms cannot. They're good for deburring and polishing small holes, narrow slots, keyways, and grooves.

These assortments include a selection of sanding sponges with long-lasting diamond abrasive on one side. Flexible enough to sand around curves and in corners, they provide the comfort and control of a sanding block.

Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.

Cut the length you need, then quickly attach, remove, and reuse.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.