These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

These lights have a longer reach and hold their position better than gooseneck-arm lights, especially around vibration.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Suspend these lights overhead or mount them above your workspace.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

With a slimmer profile than other strip machine lights, these lights fit in tight spots on workspaces and inside machinery because they don’t have a circuit board.

No need for wiring—these lights plug into a standard wall outlet. Also known as shop lights.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Link these lights together to create different shapes with a sleek look.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

Light up damp areas—these lights seal out moisture and humidity. They’ll even work in areas with frequent washdowns. Rated NEMA 4X, they withstand spraying liquid, resist corrosion, and keep out dust.

Aim light where it's needed most in areas that don't have an electrical outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Light up your work from under your brim.

Keep your hands free by wearing a flashlight on your head.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Clip these headlamps right into a mount on your tactical or rescue helmet.

More securely mounted than weighted-base magnifiers while taking up less space on your work surface, these illuminated magnifiers clamp to the side of a workbench.

Capture the extra-fine details you see under the magnifying lens in a photo or video.

Highlight fine details and defects on textured surfaces. These magnifiers cast light from an angle instead of from above like standard illuminated magnifiers.

Sturdy but flexible, these illuminated magnifiers have a weighted base to keep them still without tethering them to your workbench.

Hands-free like a benchtop magnifier and portable like a handheld magnifier, these are small enough to take with you and you don’t have to hold them.

Switch between UV light and white light to catch defects you'd otherwise miss with these hand-held magnifiers.

Spotlight fine details to find defects in parts or inspect dim machine interiors.

An LED on these loupes emits a focused, even beam so you don’t overlook any details.